Pandulipe
Plumbing

Installing a Water Heater Quickly and Flexibly: You Should Know About it

Installing a Water Heater Quickly and Flexibly

Installing a Water Heater Quickly and Flexibly

Installing a water heater is really costly nowadays. Someone professional can charge you more than 800-1000$ and additional costs are gas burning and more than fifty gallons of water. When winter is on the doorstep, warm water becomes really a necessity, and the charges for replacing a water heater can cost a big hole in your pocket.

Here, we are going to discuss how to install or replace a water heater on your own and take a nice hot shower after it’s done without costing lots of money.

Things you need: While doing the installing, you will need some specific tools and supplies they are:

  1. Tools: Hose, Tubing cutter, tape measure, and 2 pipe wrenches.
  2. Parts: A new water heater, pipe fittings, small pieces of pipe, and valves.
  3. Supplies: Towel and leak check solutions, buckets, water heater drain pan.

Let’s install New Water Heater

Installing a new water heater is not a difficult job at all, we just need to follow some simple steps. With that, a new water heater will be installed and no extra cash will be burnt. But first, make sure you really require installing a new one. If the condition is not that bad, repairing can be a great option. You can contact Top Water Heater Repair to solve the problem.  But if there is no, then here are the steps you need to follow:

  • Set The New Water Heater in place: First decide the place you want to keep your water heater. Place the new heater in a drain pan for now. You can also avoid flooding it by connecting the drain pan to the actual drain of your house.
  • Install The T&V valve: T&V valve is for safety. If the temperature or pressure of the heater reaches very high then the valve automatically opens up. If your heater doesn’t have it already installed then buy separately and install it.
  • Installing the discharge pipe: The position of the discharge pipe should be towards the floor and attached to the T&P valve. Water will drip from the pipe so make sure you have a drain or a bucket underneath the pipe.
  • Hook up the water lines: Hook up the cold water line. Hook up the hot water line. Use flexible hose kits for hookup. Apply plumbers tape to the threads of the heat trap nipples. Then attach the hoses.
  • Install And Secure the fittings: Some areas of the heater require dielectric fittings which will help in reducing the corrosion between two different metals. Add plumbers tape to the connector body threads. Secure the fitting to the hose and then hold the hose up to the pipe.
  • Now secure the compressor nuts and rings onto the pipe and tighten it.
  • Time to fill the tank: Now you need to slowly turn on the water supplies and check all the connections to make sure there is no leakage. After the confirmation of no leakage, fill the water tank. If any leakage occurs just stop the water supply and tighten the connection. Repeat this process until you feel totally secure.
  • Now flush the tank: When the water starts running from the faucet, it means that the tank is full. Then flush it so that any air or debris present in the tank comes out.
  • Connect the power source: Attach the ground wire to the green ground screw. Use masking tape and twist the end of the wires with wire connectors.
  • Now turn on the power and set the temperature: Follow the manufacturer’s instructions to set the temperature. It can take a few hours at first to heat the water.
  • As your water is heating up and the pressure is stabilized, some leakages can still reveal themselves. Fix them and you are all ready to have an invigorating hot shower.

What to do if water is leaking from the heater

Water leakage can happen in a water heater due to a number of reasons. Which includes loose valves, excessive pressure in the tanks, or the pipes or pipes that connect the units. It is better to call a plumber then. Or, you can contact top Water Heater Repair for the best service. Better you should turn off the power supply of your leaking water heater and shut off the water pressure of the tank.

New heaters can also leave water under them but it is not because of any leakage. This is because there is an insulated lining between the tank and the outer shell which gathers humidity while it is in the storage. Now when they are being heated up for the first couple of times, the trapped moisture condensates. It runs towards the bottom and onto the floor. There is nothing to be concerned about. It’ll be alright in the next couple of days.

Hopefully, the information will help you.

Leave a Comment